When a picker cannot find an item

Last updated Nov 10, 2026

Last reviewed: 2026-11-10

What this is

When a picker cannot find a unit at the bin they were sent to, they report it from the picker. CanShip takes the unit off the order's allocation, marks the order short, and flags the bin so someone counts it. It also puts the rest of that product in the bin on hold until the bin is counted, so no other order is sent to a shelf that may be short.

Report it from the picker

  1. At the location, click Can't Find on the item's line.
  2. Read the question and click Confirm.
  3. Carry on with the job. The rest of the order is picked into its tote as usual.

The line then reads Can't find reported, and the job's last screen lists what could not be found. At the packing station the order shows only the units in its tote, with a note naming the one reported missing.

What changes

  • The order reads Short in the Orders list, with Partial under Inv. Status. In the order, the line shows 0 allocated.
  • The bin reads Count requested under Inventory and under Settings > Locations.
  • Every free unit of that product in the bin goes on hold with the reason Can't Find. The picker's confirmation says how many. Under Inventory, the row shows the hold with the order and pick job it came from.
  • The Dashboard's Needs Attention card counts the bins waiting for a count and the units on hold until then. Click that line to open Settings > Locations showing only the bins with Count requested.
  • The bell in the header shows a line for the hold. See Notifications: the bell in the header.
  • Stock on hand does not change. Only the allocation is released.

Count the bin

Go to Settings > Locations, find the bin, and count it. The Count requested filter lists every bin waiting for a count.

  • If the count matches what CanShip shows, click Counted on the bin's row. The flag clears and the Can't Find hold is released, and CanShip says how many units it released.
  • If it does not match, correct the stock under Inventory > Adjust Inventory with the reason Cycle count. A count that finds fewer units can be removed even while the stock is on hold. Until you choose that reason, the bin's row says how many units are held and asks you to choose Cycle count to enter the count. CanShip confirms the bin's new quantity, that the count request is cleared, and how many units it released.

A hold someone placed by hand for another reason, such as Damaged, is not released by the count.

If you release the Can't Find hold from the Inventory page instead of counting, the stock is free again, but the bin still reads Count requested until it is counted.

While the stock is on hold

A new order for that product is saved with nothing allocated from that bin, and CanShip says why, both when the order is saved and when you click Allocate Inventory in the order. With only the Can't Find hold on the bin, it names the two ways to count it, for example RA-001: 114 units are on hold (Can't Find) at 02-CA-01-B1. Count the bin (Adjust with reason Cycle count, or Counted on Locations) to allocate them. With another hold in the bin as well, it names both and also offers the Inventory page, for example RA-001: 114 units are on hold (Can't Find, Damaged) at 02-CA-01-B1. Count the bin, or release the hold on the Inventory page, to allocate them.

Fill the order again

  1. Once there is stock for the line, open the order and click Allocate Inventory. CanShip confirms with Inventory allocated in full.
  2. On the Orders list, tick the order, click Actions and choose Add to pick job.

The new job holds only the line still to pick. Under What's in this job it also lists what is already in the order's tote. When the picker scans the unit, CanShip names the order's tote and asks them to scan it, so the unit joins the rest of the order.

Was this article helpful?

That’s Great!

Thank you for your feedback

Sorry! We couldn't be helpful

Thank you for your feedback

Let us know how can we improve this article!

Select at least one of the reasons
CAPTCHA verification is required.

Feedback sent

We appreciate your effort and will try to fix the article